How to Install a Vinyl Fence A fence made of vinyl is an attractive low-maintenance option to define property lines and keep pets and children securely confined. But, it's important to be aware of every detail when installing the fence. First, you'll need to determine the amount of posts needed and then stake out the fence line. In general fence posts should be 6 to 8 feet apart. Dig Postholes Dig postholes into your fence using a power auger or digger (check with local codes). installing vinyl fencing should measure approximately 10 inches in diameter, and deep enough to hold around one third of the length of the pole and 6 inches of gravel backfill. Gate posts and main supports must generally be six inches higher than other posts to improve strength. After digging the posts, pour approximately six inches of gravel into the holes and then fill them with concrete that sets quickly, following the mixing and setting guidelines on the concrete bag. Tap the posts that are hollow into the concrete. After that, ensure that each post is properly leveled and is level before moving on to the next. Consider installing drainage systems in case your fence is situated on top of a water source to stop water from pooling in the holes. You could also add the gravel layer between the fence and the ground to help to prevent erosion of the soil. Before you start digging, call the local utility diggers hotline and have the underground lines marked. This can help you avoid unpleasant surprises, such as the possibility of a leaky water or sewer line, while installing your fence. Once you've marked the holes, you'll need to dig each one to a depth of 2.5' to 3'. The bottom of the hole should be larger than the top of the post, in order that it will be able to fit in the post's rails when you install them. Cut Posts to Length If you're planning to construct a fence made of vinyl it is important to make sure that the posts are the same length. This is essential because it allows the fence to bend without breaking. This will ensure that the fence is able to stand up to minor impacts and high winds. You can ensure you have the exact same length of posts by using a level to measure them and marking them on a string. You can either mark the strings on the end posts, or use them to line up each posthole. Once you've marked your posts, dig holes to the appropriate depth for the fence. They should be deep enough to accommodate 3 feet of post and 6 inches of gravel. This will create the post with a base that will help drain the water away. Then, you can insert the bottom rail into each post and secure it using a self-drilling screw. This will stop the top rail from sliding away from the post and allow in-and-out movement. After the bottom rail has been put in then slide your pickets in and U-channel as necessary until you've completed the entire section. Then, you can insert your top and middle rails. When you are installing privacy fences made from vinyl be sure to install the u channel before you connect the top rail to the post. This will prevent your fence's sliding from the wind, and will also keep out dirt and bugs. Install Posts It is important to follow the instructions of the manufacturer when installing a vinyl fence. Digging holes that are deep enough to allow the posts to be supported is essential. If you are using a gravel base it will require you to dig holes 6 inches deeper. If you're installing a fence made of vinyl on a slope, it's especially critical to make sure the posts are level. This is because a high-pitched post could cause the entire fence to sag, which makes it difficult to secure the fence properly. To ensure that your posts are set straight make use of a string and tie it to each corner or end of the post prior to the time you dig the hole for it. This will help you find exactly where your posts are. To give them greater strength and stability, the posts should be at least a third deep than their length. This can be accomplished quickly and easily with a post-hole drill, or you can dig them manually. Once the posts are placed, pour concrete over them. The cement should be about one foot deep and evenly distributed. This will increase the strength of the posts and will help them withstand powerful winds. Once the posts are set After that, you can attach the rails. The rails attach to posts by snapping them into the slots at the top and bottom. Once the rails are secure they can be slid into the slots. vinyl fencing panels in place. Attach rails to posts Posts form the foundation of your vinyl fence and must be sturdy enough to withstand the weight of the fence. If the ground is sinking and the posts are unable to hold, they could shift or tipping, which could cause damage to your fence. cost to install vinyl fence to ensure the strength of your posts is to install concrete for the base. It isn't easy to attach a post to rails, however it is possible. To keep the post straight and level you can use a post brace. These are usually 2-foot by 4 feet and are attached to the post using nails or a clawhammer. After the post is secured and the rails are set on top of it. If you are installing split rails, slide the bottom rail down until it is clear of one of the posts adjacent to it. Continue to add rails until all of the posts are in place and the fence is complete. For pickets that are spaced, consult your local code enforcement for specific spacing. If your fence follows a sloped landscape, it may be necessary to cut the pickets in a stepped design. Although it is not necessary to do so, it can disguise the boards that have uneven ends. It is crucial to select the right fencing style for your property and landscaping. The fence should be in line with the overall look of your home, provide privacy and security, add curb appeal, and also add curb appeal. vinyl fence installation costs that is in the right design can reduce maintenance and repair costs. installing vinyl fencing to posts Vinyl fences are simple to install and come in a wide range of styles. They include privacy fences, picket fences and split rail fences. They are an attractive alternative to wood fences due their durability and low maintenance. Before you dig holes for the posts, take a measurement of the distance between each of the posts to make sure that the fence is constructed in an even line. Then use a string to mark and place the posts. After the posts are ready to be erected, you must dig holes for each post leaving 5 to 6 inches above the ground. You may also apply concrete to the base of each post if you have a sloped property. Once the posts have been installed, you can add fence rails to them. Vinyl fence rails are available in two lengths, 8-foot and 16 so you can decide the size that best suits your home. If the fence has corners, you'll need to cut the rails to fit around the corner. To slide the rail through the posts that are at the corners, you can use one end of the rail and the opposite end to slide it into a different post. After attaching the rails put the fence pickets on the rails. This will create a neat, professional look for your fence. This will let you visually grade your fence to ensure it appears consistent. Attach posts to other posts Vinyl fences are a great option for homeowners looking to improve their property's curb appeal, privacy, and shield their gardens from weather damage. They are durable and require little maintenance. There are a myriad of styles of vinyl fences, including solid privacy, picket and many more. You can choose from a variety colors and dimensions of fences. Some even have a lifetime warranty. When you are choosing a fence made of vinyl for your home, consider the manufacturing process employed by the manufacturer. Vinyl fencing can be produced in two primary ways: monoextrusion or co-extrusion. The first method injects polyvinyl chloride with UV inhibitors to stop fade and chalking. The latter method utilizes a double-layer of PVC to create a capstock and substrate. Vinyl fences are also injected with stabilizers, impact modifiers and other substances that make them tough and flexible. They are also resistant to rot and decay and some are covered by the lifetime guarantee. If you're uncertain about the kind of fence you want to purchase, ask your local dealer for suggestions. They can help you find the right product for your needs and help you make your choice. After cost to install vinyl fence 've selected a vinyl fence for your home and you're ready to begin the installation. This portion of the job isn't easy and it's crucial to follow the steps carefully.
installing vinyl fencing|cost to install vinyl fence|vinyl fence installation costs|installing vinyl fencing|cost to install vinyl fence
